BYD Seal electric sedan
BYD Seal Sedan Body, Lamps & Door Parts Guide
The original Seal has a sedan boot lid, not a glass-carrying SUV liftgate.
Start with the sedan body configuration
Keep the exact market, build date and panel photographs with the inquiry. A Seal U or DM-i body listing must not be carried into the electric-sedan quotation.
Break the front end into supplied assemblies
A bumper shell, lower trim, active grille shutter, headlamp and support carrier are separate order lines. Decide what is retained and what needs replacement after inspection. Match sensor and bracket openings before paint or assembly work.
Identify the lamp section and traffic market
Separate front headlamps, rear corner lamps and the centre light bar. Confirm legal beam-market requirements, connectors and included control modules. A supplier description claiming universal steering compatibility does not establish the lamp approval needed for the destination.
Keep concealed handles and door equipment distinct
Identify front or rear door and side, then record the handle mechanism, keyless functions, latch and window regulator. A painted handle skin is not the complete actuating assembly. Check the complete window frame and glass-channel geometry on the actual door before comparing shell and regulator interfaces.
Specify boot support and lock contents
Confirm the installed boot support type and its own markings. UK 2026 specifications describe powered opening, but do not establish the equipment of every earlier import. Separate lid shell, hinges, support, latch and closing equipment to avoid incomplete or duplicated packages.
Agree bare versus equipped body supply
State whether a door or lid is a bare shell or carries glass, wiring, locks and trim. Specify finish, protected edges and packing support. Keep camera or sensor configuration requirements attached to the equipment being transferred or replaced.
Related selection checks
After front cooling-pack damage, inspect the cooling fan assembly and radiator support mountings alongside the active grille shutter; confirm clearance to the motor cooling radiator.
Compare the panel junctions between the front bumper, headlights, fender and hood before approving front-end body parts for the same revision.
Keep the rear body revision with the rear bumper, installed tail lights section and trunk lid; identify each parking sensor location separately from the surrounding trim.
Components to identify separately
| Assembly | Selection record |
|---|---|
| Headlights | Side, body revision, beam-market approval and control modules |
| Tail Lights | Outer corner, centre light bar or separate rear lamp function |
| Front Bumper | Cover revision, lower grille, parking holes and radar interfaces |
| Rear Bumper | Upper cover, lower trim, reflectors and sensor positions |
| Side Mirror | Door side, steering market, base and fitted electrical functions |
| Fender | Side, arch contour, flange holes and panel junctions |
| Hood | Outer contour, hinge spacing, latch position and inner frame |
| Trunk Lid | Sedan boot opening, hinge geometry, lamp and latch interfaces |
| Door Shell | Front/rear door, side, window frame and hinge geometry |
| Window Regulator | Door corner, rails, glass clamps, cable routing and motor |
| Door Lock Actuator | Door corner, latch jaw, release cables and connector |
| Exterior Door Handle | Door corner, concealed-handle mechanism, sensor and finish |
| Trunk Lock Actuator | Boot-lid latch, striker alignment, release and electrical plug |
| Trunk Support | Actual gas or powered support, installed side and mounting ends |
| Wiper Motor & Linkage | Front sweep mechanism, LHD/RHD, pivots and motor plug |
| Washer Pump | Tank socket, outlet arrangement, seal and electrical plug |
| Washer Reservoir | Tank contour, filler route, pump recess and level-sensor provision |
| Fender Liner | Wheel corner, coverage, fastener pattern and adjoining panels |
| Underbody Shield | Front/centre/rear position, panel outline and mounting pattern |
| Radiator Support | Front carrier, cooling-pack mounts, lamp tabs and latch interface |
| Active Grille Shutter | Louvre frame, actuator, connector and bumper revision |
| Charge Port Door | Exterior flap, hinge, latch and body aperture |
| Parking Sensor | Bumper position, seating ring, signal interface and connector |
| Reversing Camera | Rear-view or surround-view system, housing and video interface |
Continue the order
Return to the Seal system directory. For commercial information, use the parts-list quotation guide; keep vehicle-specific identification with each requested assembly.
Auto parts inquiry
Send the vehicle and part evidence.
Include brand, full model, year, engine or EV drivetrain, OE/material code, quantity, destination and packing request. You can attach a list or old-part photos.